EARTHING, BONDING, LIGHTNING & SURGE PROTECTION of Electrical and Electronic Systems & Equipment – YOGYAKARTA

[S130]

WAKTU

Silahkan Pilih waktu yang anda inginkan dan tulis di form pre registration :

1-3 February 2012 / 15-17 May 2012 / 6-8 June 2012

TEMPAT

Hotel Ibis Yogyakarta

INVESTASI

IDR 5.500.000 per participant – non residential

INSTRUKTUR

Tugino, ST MT

DESKRIPSI

Few topics generate as much controversy and argument as that of grounding and the associated topics of surge protection, shielding and lightning protection of electrical and electronic systems. Poor grounding practice can be the cause of continual and intermittent difficult-to-diagnose problems in a facility. This workshop looks at these issues from a fresh yet practical perspective and enables you to reduce expensive downtime on your plant and equipment to a minimum by correct application of these principles.

OBJECTIVES
1. Apply the various methods of grounding electrical systems
2. Detail the applicable national Standards
3. Describe the purposes of grounding and bonding
4. List the types of systems that cannot be grounded
5. Describe what systems can be operated ungrounded
6. Correctly shield sensitive communications cables from noise and interference
7. Apply practical knowledge of surge and transient protection
8. Troubleshoot and fix grounding and surge problems
9. Design, install and test an effective grounding system for electronic equipment
10. Understand lightning and how to minimize its impact on your facility
11. Protect sensitive equipment from lightning

OUTLINE
1.Introduction And Basics
Fundamentals of grounding
– bonding
– lightning
– surge protection
– shielding

2.Recommended Design And Installation Practices
o Wiring and grounding for safety and performance
o Wiring and distribution systems
o Dedicated and derived neutral systems
o Grounding and bonding equipment

3.Fundamentals Of Grounding For Building Electrical Systems
o Grounding of building systems
o Which electrical systems can be operated ungrounded
o Proper methods of grounding building electrical systems
o Location of the service grounding connection
o Proper sizing of grounded (neutral) conductors

4.Typical Rules To Be Applied
o Rules for multiple services to one building
o Rules for low impedance and high impedance systems
o Rules for bonding requirements at building service equipment
o Grounding electrodes, systems and conductors
o Bonding enclosures and equipment
o Equipment grounding conductor types
o Enclosure and equipment grounding
o Grounding of separately derived systems

5. Grounding And Noise Control
o Misconceptions of performance grounding
o Single point versus multi point techniques
o Noise and zero signal reference grid
o Avoiding non recommended practices
o Shielding

6. Electrical Faults
o Ground fault circuit interrupters
o Equipment ground fault protection systems

7. Applications Of Grounding And Bonding
o Grounding and bonding in hazardous (classified) locations
o Grounding and bonding for health care
o Grounding and bonding for swimming pools, hot tubs and spas
o Static and electricity: grounding and bonding requirements
o Common violations
o Building electrical inspection procedures
o How to recognize hazards

LIGHTNING
o Need for a lightning protection system
o Which protection systems work and which don’t
o Best location for IT equipment
o Optimum grounding for building
o Pitfalls of isolated grounding
o Shielding and bonding of electronics and communications
o Optimum location of surge protection devices

SURGE AND TRANSIENT PROTECTION
o Lightning phenomena
o Protection of power supply
o Protection of electric communications circuits
o Power system faults and switching surges
o Mitigation techniques
o Case studies

POWER CONDITIONING
o Power conditioners
o Uninterruptible power systems
o Power quality alternative sources

INSTRUCTOR
Tugino, ST MT

WHO SHOULD ATTEND?
Instrumentation & Control Engineers, Consulting Engineers, Electrical Engineers, Project Engineers, Maintenance Engineers, Electrical Contractors,Safety Professionals, Consulting Engineers, Electricians, Electrical Inspectors, Power System Protection & Control Engineers, Building Service Designers, Data Systems Planners and Managers, Electrical and Instrumentation Technicians

DELIVERY TYPE
Lecturing, interactive discussion, presentation, and case study.

FACILITIES
” Training module (hardcopy & softcopy)
” Stationeries: notebook and ballpoint
” Training bag or backpack
” 1x lunch & 2x coffee break at days of training
” Exclusive T-Shirt
” Certificate
” Training photo
” Transportation for participants from the airport/railway station to hotel/training venue (Minimal number of participants from the same company is 2 persons)

NFORMASI PENDAFTARAN
Ketik SMS dengan format :
DAFTAR<spasi>
JUDULTRAINING#TGLTRAINING#NAMA#PERUSAHAAN#JMLHPESERTA#EMAIL
-kirim ke 085286451074

Contoh :
DAFTAR TRAINING ISO#2Mei2011#ARIEF#Company#3#nama@email.com

atau ISIKAN FORM BERIKUT :

Print This Post Print This Post Email This Post Email This Post


Cara cepat dan mudah Registrasi online di Informasi seminar 21. Mencari jadwal seminar dan training atau request in-house training online.
INFOSEMINAR21 | INFOTRAINING21

Share

Comments are closed.

Post Navigation

Share